AeroCool ExtremEngine 3T- ATX-Micro ATX Case -Silver

Features:
1. Powerful 25cm fan with incredible airflow at side panel!
2. 3 Aluminum turning knobs control the speed of 25cm fan at side panel, 14cm fan at front bezel and one user defined fan
3. Uniformity of jet engine theme design at front bezel and side panel
4. Meshed 5.25" bay covers for greater air flow through out the case
5. 2-Piece elegantly brushed aluminum front doors
6. IEEE1394 / 2 x USB2.0 / Mic + Earphone

Futuristic styled design with aluminum front doors	Powerful 25cm fan with incredible airflow at side panel!
Jet engine styled propeller design	Fan controller controls 25cm fan(side),14cm fan (front) and user defined fan 1394 / USB / Mic / Earphone
Meshed 5.25" bays for better air flow	Supports up to 2x80mm fan or 1x120mm fan at rear of case

Specifications:
Material SECC 0.6mm
Motherboard ATX / Micro ATX
Drive Bay 4 x 5.25" / 1 x 3.5" / 6 x Hidden
Cooling System

(with fan controller)
Front 1 x 14cm fan with quad blue LEDs
Speed: 650~1500 RPM
Air Flow: 68.37 CFM (MAX)
Noise: 17.8~34.72dB(A)
Side 1 x 25cm fan
Speed: 550~1000 RPM
Air Flow: 90.97~162.82 CFM (MAX)
Noise: 19.54~35.28 dB(A)
Expansion Slot 7
Front I/O Port IEEE1394 / 2 x USB2.0 / Mic+Earphone
Chassis Dimensions 440mm (D) x 430mm (H) x 200mm (W)

Cable Installation Guide
Due to the tag and pin assignment of front panel connector may vary for different type of motherboard, we can only provide a general guideline for the wire connection. You should refer to your motherboard installation manual for detail. FRONT PANEL CONNECTORSConnect RESET SW, POWER SW, POWER LED, HDD LED and SPEAKER to correspondent front panel connectors of motherboard.

FRONT PANEL AUDIO CONNECTORS
a. Connect MIC VCC (MIC POWER or MIC_BIAS) and MIC DATA (MIC_IN or MIC) to correspondent motherboard connector for microphone input. (Pin#3 and Pin#1 in 10-pin audio connector)
b. Connect EAR_L to (SPK L or L_OUT or L) and EAR_R to (SPK R or R_OUT or R) for headphone or audio output for left and right channel respectively. (Pin#9 and Pin#5 in 10-pin audio connector)
c. Connect extra (black color wire) EAR_L and EAR_R to R-RET (or NEXT_R) and L-RET (or NEXT_L) for Rear/Back panel headphone or audio output (Pin#10 and Pin#6 in 10-pin audio connector). It will send a signal to system to disable the rear audio output when front panel output device was connected. (Note: Some motherboard might not have R-RET and L-RET connectors then just leave these connectors alone.)

FRONT PANEL USB CONNECTORS
Some motherboard may have more than two pairs of front panel USB connector, you can pick any pair of USB port and leave the extra USB port alone. Once you select USB port on your motherboard, follow the pin assignment of your motherboard, connect USB connectors to the corresponding USB front panel connector on your motherboard,Connect USB connectors VCC to USB power port (or USB+5V), USB1-/USB2- to USB data port “–“ (-D or USB-), USB1+/USB2+ to USB data port “+” (+D or USB+), GND to GROUND (GND) and leave extra connectors such as NC (Normal Closed) or GND alone. (Note: Please pay attention on USB pin connection, wrong wire connection will cause USB device damaged)

IEEE-1934 CONNECTOR
Connect TPA+, TPA-, TPB+, TPB-, VP, VG, GND (SHIELD) to IEEE1934 (Firewire) connector. Depend on your motherboard, if your motherboard did not provide this kind of connector then just neglect it.

FAN CONNECTOR
Connect case fans’ 4-pin power connector to any 4-pin power connector from the power supply. For 3-pin power connector case fans, you can connect it directly to any 3-pin connector of motherboard or fan controller, or add 3-pin to 4-pin converter then you can connect them to any 4-pin power connector from the power supply.

10%

Details


SKU	841269050534
Weight	20.00 lbs
Price:	$94.95

Options

Quantity

Add to cart

Add to wish list