AeroCool AeroEngine II Case- Silver

Click for More Images!

Features:

Jet Engine styled design for smooth and quiet air inlet to keep case cool
Fitted with quad blue LED 14cm fan at front of case to withdraw cool air with a strong air pressure and one 12cm transparent fan at rear of case
Meshed 5.25" bay covers
Pulling handles installed at the side panel for easy pulling
Clear acrylic side window supports upto 2x12cm and 2x8cm fan installation.
2 piece plastic front door

Specifications:

Material 0.65mm SECC
Motherboard ATX / Micro ATX
Drive Bay

Exposed 5.25" x 4
3.5" x 1

Hidden

3.5" x 6

Cooling System

Front

14cm
1000RPM / Current:0.23A
Power: 2.76W / Flow: 45.58CFM
Noise: 26.91dBA

Rear

12cm
1500RPM / Current:0.23A
Power: 2.76W / Flow:
59.12CFM

Expansion Slots: 7

Front I/O port
USB2.0 x 2
IEEE 1394 x 1
Audio x 1
Mic x 1

Net Weight 6.3Kg
Dimension 200 (W) x 430(H) x 440(D) mm

Cable Installation Guide
Due to the tag and pin assignment of front panel connector may vary for different type of motherboard, we can only provide a general guideline for the wire connection. You should refer to your motherboard installation manual for detail.
FRONT PANEL AUDIO CONNECTORS

a. Connect MIC VCC (MIC POWER or MIC_BIAS) and MIC DATA (MIC_IN or MIC) to correspondent motherboard connector for microphone input. (Pin#3 and Pin#1 in 10-pin audio connector) .
b. Connect EAR_L to (SPK L or L_OUT or L) and EAR_R to (SPK R or R_OUT or R) for headphone or audio output for left and right channel respectively. (Pin#9 and Pin#5 in 10-pin audio connector)
c. Connect extra (black color wire) EAR_L and EAR_R to R-RET (or NEXT_R) and L-RET (or NEXT_L) for Rear/Back panel headphone or audio output (Pin#10 and Pin#6 in 10-pin audio connector). It will send a signal to system to disable the rear audio output when front panel output device was connected. (Note: Some motherboard might not have R-RET and L-RET connectors then just leave these connectors alone.)

FRONT PANEL USB CONNECTORS

There are two sets of internal USB connectors (USB1 and USB2), connect USB connectors to the corresponding USB front panel connector on your motherboard, some motherboard may have more than two pairs of front panel USB connectors then leave the extra USB port alone.
Connect USB connectors VCC to USB power port (or USB+5V), USB- to USB data- (-D or USB-), USB+ to USB data+ (+D or USB+), GROUND to GROUND (GND) and leave rest of connectors such as NC (Normal Closed) or extra GND alone.

IEEE-1934 CONNECTOR

Connect TPA+, TPA-, TPB+, TPB-, VP, VG, GND (SHIELD) to IEEE1934 (Firewire) connector. Depend on your motherboard, if your motherboard did not provide this kind of connector then just neglect it.

FAN CONNECTOR

Connect case fan 4-pin power connector to any 4-pin power connector from the power supply.

1. Remove side panel.
2. Push the metal plate at lower half.

3. Push the metal plate at upper half.
4. Repeat 2 and 3 until the metal plate breaks off.

5. Apply some force to the bay cover and push from outside to remove it.

17%

Details


SKU	841269020428
Weight	18.00 lbs
Price:	$74.95

Options

Quantity

Out of stock

Notify Me